OUTEX.F-STEP

F STEP (All-Purpose)

Click here for F PEG for off road

Road model’s first biaxial slant system

Body to bike motion control

.

. Features of OUTEX.F-STEP

Since the F-STEP has a broader surface and the sole is always in contact during riding, the load is evenly distributed.

The forward and backward motion of the F step along the axis of the shaft, increases shift change and rear break control performance.

With a sense of unity between steady footwork and the body of the motorcycle, cornering stability is improved.

Follows all riding positions including acceleration, deceleration and standing, however the peg load does not change.

Alleviates fatigue even when touring long distance, and reduces shift misses, so you can concentrate on riding.

Vibration decreases in comparison with an normal peg.

The height for anti-slip screw can be adjusted.

The angle for F-STEP can be adjusted.

F-Step is foldable to reduce damage caused by falling down. (F-STEP is normally not folded since　F STEP is fixed with the bolt.)

Made of aluminum A2017 for the peg.

F-STEP can be installed to commercial rear set foot rest.

Should damage occur, replacement parts can be ordered individually.

OUTEX.F-STEP Silver Anodized M10 (All-purpose)Part number FS10C70 Price 240 USD

. .

. .

. .

The angle can be adjusted by adding collars. The height of anti-slip screw can be adjusted.	F-STEP can be foldable to reduce damage caused by falling down.
The maximum angle is 50 degrees. F-STEP fits the sole of a boot and easy to change gears.

Leg power axis point

F STEP has a broader surfase. So, the outside of F STEP touches the sole firmly! Outside: Contact area with the sole. Outside: Contact area with commercial setp bar.

The load around the tow is distributed since a wide surface of F STEP. So, good traction! Inside: Contact area with the sole. Inside: Contact area with commercial step bar.

The length and the bolt size for F STEP

Length 80 mm x width 45 mm/ The length of the bolt need to be fitted the structure of your step.

F-STEP can be installed to commercial rear set foot rest. Check the bolt size.(See the table below �A) How to install F STEP
1. Take off Step bar and Main plate.	2. Check the thickness for main plate, collar and axis of brake laver. The total length of them is 33 mm. So, the length of the bolt is 95 mm.
3. Insert the bolt to brake lever, colar and main plate.	4. Mount the nut on the back of main plate. Fasten them according to your favorite angle.
5. Adjust the position of brake laver and shift laver.
Done!

..

F STEP Line-up / 240 USD

Product Name/Bolt length	Part number（M8）	Part number（M10）	Tickness of mountaing parts
F STEP / 70mm	FS8-70	FS10-70	〜12mm
F STEP / 75mm	FS8-75	FS10-75	〜17mm
F STEP / 80mm	FS8-80	FS10-80	〜22mm
F STEP / 85mm	FS8-85	FS10-85	〜27mm
F STEP / 90mm	FS8-90	FS10-90	〜32mm
F STEP / 95mm	FS8-95	FS10-95	〜37mm

�@ 　Confirm the bolt size for your step bar in use and the thickness of mounting parts.

�A 　Choose the bolt size ( M8 or M10) and the bolt length from the above table.

�B 　Choose your favorite Anodized color from Sliver or Black.

Contact us about other bolt size.

Option Spacer

Spacer is used when putting out F Step outward.

10mm Spacer x2 Choose the length of the bolt.

　

The length of F STEP can be adjusted with Option spacer.

Examples of fitting

2017 Tsukuba Road Race Championship TC400 Masato Nakashima R3 Win！ R4 3rd！

Triple Clamp Stabilizers　　Fork Springs　　Under Frame　　Adjustable Link Rod　

Clear Tubeless Kit　　Spoke Boosters　　OUTEX Full Exhaust Muffler　　Rear Spring　　Lever Guards

OUTEX

OUTEX Online Shop