OUTEX CLEAR TUBELESS KIT

Supplementary Instructions for Masking Tape@

 

šAffix masking tape to both edges of the rim depression, making it easier to affix double sided tape.

Please proceed to 1, after completing the preprocessing before affixing the double sided tape.

(Refer to the instructions included with the product)

 

Description: C:\Users\OUTEX\Documents\001¤•iŽÊ^Aƒf[ƒ^\1ƒ`ƒ…[ƒuƒŒƒXƒLƒbƒg\ƒn[ƒŒ[ƒ_ƒrƒbƒhƒ\ƒ“\à–¾‘—pFR-HD255\HD255A.JPG

1. Cut off about 5mm of double sided tape and affix it in the center of the rim depression. Use a magic marker to mark both edges of the double sided tape.

Description: C:\Users\OUTEX\Documents\001¤•iŽÊ^Aƒf[ƒ^\1ƒ`ƒ…[ƒuƒŒƒXƒLƒbƒg\ƒhƒJƒeƒB[\ƒXƒNƒ‰ƒ“ƒuƒ‰[\2.JPG

2. Using the magic marker marks as a guide, affix masking tape all the way around.

Description: C:\Users\OUTEX\Documents\001¤•iŽÊ^Aƒf[ƒ^\1ƒ`ƒ…[ƒuƒŒƒXƒLƒbƒg\ƒhƒJƒeƒB[\ƒXƒNƒ‰ƒ“ƒuƒ‰[\3.JPG

3. After affixing it completely straight all the way around, go foward pressing it down to match the height of the magic marker marks.

Description: C:\Users\OUTEX\Documents\001¤•iŽÊ^Aƒf[ƒ^\1ƒ`ƒ…[ƒuƒŒƒXƒLƒbƒg\ƒhƒJƒeƒB[\ƒXƒNƒ‰ƒ“ƒuƒ‰[\5.JPG

4. Masking complete.

 

Description: C:\Users\OUTEX\Documents\001¤•iŽÊ^Aƒf[ƒ^\1ƒ`ƒ…[ƒuƒŒƒXƒLƒbƒg\ƒhƒJƒeƒB[\ƒXƒNƒ‰ƒ“ƒuƒ‰[\6.JPG

5. While sliding both edges of the double sided tape, and ensuring that it doesn't become uncentered, go forward affixing it to the nipple surfaces. After affixing it all the way around, cut it off from the roll using scissors.

 

Description: C:\Users\OUTEX\Documents\001¤•iŽÊ^Aƒf[ƒ^\1ƒ`ƒ…[ƒuƒŒƒXƒLƒbƒg\ƒhƒJƒeƒB[\ƒXƒNƒ‰ƒ“ƒuƒ‰[\8.JPG

6. Affix it while pressing out the air between the double sided tape and rim. Next, use a utility knife with a fine tip to cut a hole for the valve.

Description: C:\Users\OUTEX\Documents\001¤•iŽÊ^Aƒf[ƒ^\1ƒ`ƒ…[ƒuƒŒƒXƒLƒbƒg\ƒhƒJƒeƒB[\ƒXƒNƒ‰ƒ“ƒuƒ‰[\9.JPG

7. Peel off the green release film.

Description: C:\Users\OUTEX\Documents\001¤•iŽÊ^Aƒf[ƒ^\1ƒ`ƒ…[ƒuƒŒƒXƒLƒbƒg\ƒhƒJƒeƒB[\ƒXƒNƒ‰ƒ“ƒuƒ‰[\10.JPG

8. Put the valve through the hole in the protective sheet, and affix the protective sheet. Ensure that the protective sheet doesn't become uncentered from the rim center, and at this point it is okay to affix it lightly as in the image.

After affixing it all the way around, cut the protective sheet once.

Description: C:\Users\OUTEX\Documents\001¤•iŽÊ^Aƒf[ƒ^\1ƒ`ƒ…[ƒuƒŒƒXƒLƒbƒg\ƒhƒJƒeƒB[\ƒXƒNƒ‰ƒ“ƒuƒ‰[\11.JPG

9. First, press down the center of protective sheet all the way around.

Description: C:\Users\OUTEX\Documents\001¤•iŽÊ^Aƒf[ƒ^\1ƒ`ƒ…[ƒuƒŒƒXƒLƒbƒg\ƒhƒJƒeƒB[\ƒXƒNƒ‰ƒ“ƒuƒ‰[\12.JPG

10. Avoiding damage to the protective sheet, push out the air  from the protective sheet on the circumference using a tire lever with a round tip, etc.

Description: C:\Users\OUTEX\Documents\001¤•iŽÊ^Aƒf[ƒ^\1ƒ`ƒ…[ƒuƒŒƒXƒLƒbƒg\ƒhƒJƒeƒB[\ƒXƒNƒ‰ƒ“ƒuƒ‰[\13.JPG

11. Press out the air.

Description: C:\Users\OUTEX\Documents\001¤•iŽÊ^Aƒf[ƒ^\1ƒ`ƒ…[ƒuƒŒƒXƒLƒbƒg\ƒhƒJƒeƒB[\ƒXƒNƒ‰ƒ“ƒuƒ‰[\14.JPG

12. Please cut the protective sheet with a utility knife avoiding overlapping

It is okay if there is a slight gap.

Description: C:\Users\OUTEX\Documents\001¤•iŽÊ^Aƒf[ƒ^\1ƒ`ƒ…[ƒuƒŒƒXƒLƒbƒg\ƒhƒJƒeƒB[\ƒXƒNƒ‰ƒ“ƒuƒ‰[\15.JPG

13. Firmly press down both edges using a plastic spatula, etc.

 

18

14. Affix the double sided tape, hologram sticker, and protective sheet onto the seam in that order.

 

For the rest, refer to the instructions included with the product.

 

 

OUTEX